复杂环境下氧化铝储槽定向爆破拆除

在较为复杂的环境下,爆破拆除钢筋混凝土氧化铝储槽。该储槽自重大、呈圆形,内有4根立柱支撑下料漏斗。为使储槽顺利定向倒塌,通过爆破方案选择、参数确定,采取梯形切口和预处理以及安全防护和减振措施,使储槽爆破拆除获圆满成功。     

基于FLAC3D的破碎围岩巷道支护效果分析

为了解破碎围岩分别采用锚杆支护、锚喷支护以及锚喷+锚索耦合三种支护方式下的支护效果,进而为破碎围岩巷道选择合理的支护方式提供参考。通过借助FLAC^3D软件建立数值模型,分析不同支护条件下的破碎围岩巷道位移量、应力分布以及塑性区的时空演化特征。结果表明,采用锚喷+锚索耦合支护时,可以较好的控制巷道围岩的位移量、减小应力集中效应、缩小塑性区的影响范围。     

建筑物掏土纠倾法单孔与多孔塑性区特性研究及工程应用

在建筑物水平掏土纠倾工程中，掏土孔间距是影响纠倾工程安全与工期的重要因素。为了快速准确地确定纠倾工程中的水平掏土孔间距，研究了单个掏土孔和多个掏土孔情况下孔周边土体塑性区发展特性。利用土体塑性力学分析计算得到了单孔下的孔周土塑性区半径，而后通过有限元模拟得到孔周土体塑性区半径的数值解，将孔周塑性区半径解析解与数值解进行了对比。并通过有限元数值模型研究了多个掏土孔相互影响情况下的塑性区发展规律，以孔间土体塑性区贯通时的距离作为掏土孔间距。考虑土体参数随机特性的影响，研究不同上部荷载作用下掏土孔间距的取值变化规律，上部面荷载与地基承载力特征值比值用p表示，孔间距与掏土孔直径比值用n表示。研究发现：多孔塑性区半径（孔间塑性区贯通时）是单孔塑性区半径的1.3倍左右;标准化荷载p与孔间距比值n二者呈线性关系;通过不同土体参数及上部荷载的不同情况下的p-n曲线，给出了掏土孔间距建议值。同时，将研究结果与三个实际工程进行对比，发现p-n曲线法与实际结果更为接近。     

基于数值模拟的挤压参数对AZ91镁合金管转角焊合室分流挤压焊合压力的影响规律研究

提出了一种镁合金管材转角焊合室分流挤压新工艺，该工艺可在有效延长焊合室长度和焊合时间前提下保证舌针刚度，从而保证管材尺寸精度，并且可通过转角剪切变形机制增加预焊合金属变形量和动态再结晶程度，从而有利于提高管材性能和焊缝焊合性能。利用有限元法揭示了转角焊合室分流挤压成形过程中金属的流动特征，应变分布特征和焊合室内的静水压力分布特征。结果表明，整个挤压过程无金属折叠，从而保证管材的表面质量；流经转角后预焊合金属变形量明显增加，有利于提高管材质量和焊缝质量。最后，研究揭示了坯料初始温度，挤压速度和模具转角对焊合室内静水压力的影响规律。结果表明，随着挤压速度的增加和模具转角的增大，转角焊合室内静水压力增大；随着坯料预热温度的增加，转角焊合室内静水压力呈先增大后减小的趋势。     

汽车加油口双色注射模设计

分析了汽车加油口塑件结构,确定了注射成型方案、进胶方式,并介绍了通过滑块与开模动作配合实现塑件脱模的过程。     

非径向管板焊接接头的超声检测

对AP1000压水堆核电站安全壳贯穿件的非径向管板焊接接头结构特点进行了介绍,并分析其超声检测工艺的重点和难点。通过建立统一的缺陷定位坐标系并结合被检构件的几何特点进行综合分析,推导得出了h值(缺陷回波最高点距套管外壁的距离)的计算方法。为超声检测对这类焊接接头缺陷的准确识别和定位提供了行之有效的方法,为解决这类焊接接头的超声检测技术受限区提供了行之有效的措施。     

我国中空吹塑行业发展现状及“十四五”期间重点产品、工艺和设备发展方向

从原料、中空成型机和吹塑工艺等方面介绍了我国中空吹塑行业发展现状，并对电子化学品专用超洁净桶、高压储氢四型瓶、全电动中空成型机、微发泡中空成型技术和挤吹聚对苯二甲酸乙二醇酯（PET）容器等在“十四五”期间的重点产品、工艺和设备发展方向进行了展望。     

An integrated model for analysing the effects of ultrasonic vibration on tool torque and thermal processes in friction stir welding

An integrated model of ultrasonic vibration enhanced friction stir welding (UVeFSW) is developed by integrating the thermal-fluid model with the ultrasonic field model and tool torque model. The tool torque and the heat generation rate at tool/workpiece contact interfaces are coupled with the interfacial temperature, strain rate and ultrasonic energy density. The model is used in quantitatively analysing the effects of ultrasonic vibration on tool torque and thermal processes in friction stir welding (FSW). The results show that ultrasonic vibration reduces the flow stress, which results in a decreasing of tool torque, interfacial heat generation rate and interfacial temperature. The complicated interaction of ultrasonic energy with the thermal processes in FSW leads to a gentle thermal gradient and an enhanced plastic material flow in UVeFSW. The model is validated by a comparison of the calculated thermal cycles and tool torque at various welding parameters with the experimentally measured ones.     

Measurement of residual stresses in dissimilar friction stir-welded aluminium and copper plates using the contour method

The longitudinal residual stresses in the friction stir-welded plates of 5A06 aluminium and pure copper were determined using the contour method. The results revealed the presence of high tensile and compressive residual stresses on the aluminium and copper sides, respectively. The residual stresses were detected on the weld zone as well as the thermo-mechanically affected zone (TMAZ) of the aluminium plate. In contrast, the compressive residual stresses in the copper plate had a much narrower width along the weld line. Peak tensile stresses up to 240?MPa were found in the TMAZ of the aluminium plate.     

Effect of metallurgical evolution during post-weld aging treatment on localised corrosion of resistance spot welding joints of A286 superalloy

The combined effect of resistance spot welding and precipitation hardening on the localised corrosion of A286 superalloy is studied. The specimens tested by double loop electrochemical potentiokinetic reactivation were welded in the solution treated condition, and then subjected to different precipitation hardening treatments. For both base metal and weld nugget, the maximum localised corrosion is reached when η phase is clearly observable. The fact that the localised corrosion resistance of weld nugget is different from that shown by base metal may be explained by the segregation of Ni and Ti towards the interdendritic region of weld nugget (studied by using scanning electron microscope/energy dispersive X-ray analysis).